8-hour TWA exposure calculator
Short answerAn 8-hour time weighted average (TWA) is each measured concentration multiplied by the hours it lasted, added together, then divided by 8. The result is compared with the 8-hour exposure limit for that substance. For example, 2 hours at 150 ppm, 2 hours at 75 ppm and 4 hours at 50 ppm give 81.25 ppm.
What the TWA calculator works out
Most occupational exposure limits for airborne chemicals are written as an 8-hour TWA, because for many substances the total daily dose drives the health effect. Comparing one spot reading directly with an 8-hour limit is a common mistake that can raise a false alarm or hide a real overexposure.
Enter each sample as a concentration and a duration in hours, in any consistent unit (ppm or mg/m3). Optionally add the exposure limit in the same unit and the calculator shows the TWA as a percentage of it.
The 8-hour TWA formula
This is the same form OSHA uses for cumulative exposure in 29 CFR 1910.1000(d)(1)(i).
- 8-hour TWA = (C1 x T1 + C2 x T2 + ... + Cn x Tn) / 8
- C = measured concentration, T = hours at that concentration
- Percent of limit = TWA / exposure limit x 100
Worked example
This example is the one OSHA gives in 1910.1000(d)(1)(ii). The 8-hour limit is 100 ppm. The worker spends 2 hours at 150 ppm, 2 hours at 75 ppm and 4 hours at 50 ppm.
TWA = (2 x 150 + 2 x 75 + 4 x 50) / 8 = (300 + 150 + 200) / 8 = 650 / 8 = 81.25 ppm.
That is 81% of the 100 ppm limit, so the 8-hour limit is not exceeded, even though one period was 50% above it.
How to read the result
Above 100% of the limit means the 8-hour exposure limit is exceeded. OSHA 8-hour TWA limits apply to any 8-hour shift of a 40-hour week (1910.1000). Many organisations start action at 50% of the limit, and some substance-specific OSHA standards set a formal action level, often at half the limit. The calculator shades results above 50% as a warning and above 100% as an exceedance.
What the calculation does not tell you
- Unsampled time counts as zero. Six hours sampled at 40 ppm gives 240 / 8 = 30 ppm. If the worker was exposed during the missing two hours, the real TWA is higher.
- It does not test short-term (STEL) or ceiling limits. OSHA ceiling values must not be exceeded at any time, and a brief spike can breach them while the TWA looks fine.
- It makes no allowance for skin absorption, mixtures with additive effects, or extended shifts, which may need adjusted limits.
- It always divides by 8, so if the hours entered add up to more than 8, every hour is still counted.
- Sampling method, accuracy and the right limit for your jurisdiction need a competent person. Follow site procedures.
Questions people ask
How do you calculate an 8-hour TWA?
Multiply each measured concentration by the hours it lasted, add the results and divide by 8. For example, 4 hours at 30 ppm and 4 hours at 10 ppm gives (120 + 40) / 8 = 20 ppm. Use the same unit for every sample and for the limit you compare it with.
What happens if I only sampled part of the shift?
The calculator treats unsampled time as zero exposure and still divides by 8. That is correct only if there was genuinely no exposure in that time. If exposure continued, the result understates the true TWA. Sample the full shift where you can, or have a competent person judge the missing period.
What is the difference between TWA, STEL and ceiling?
The TWA is the average over an 8-hour shift. A short-term exposure limit (STEL) is usually a 15-minute average that must not be exceeded at any time in the shift. A ceiling is an instantaneous level that must never be exceeded. One substance can have all three, and each must be checked separately.
Can I use mg/m3 instead of ppm?
Yes. The formula works in any concentration unit, as long as every sample and the exposure limit are in the same one. Converting between ppm and mg/m3 needs the substance's molecular weight and the reference temperature and pressure, so do that conversion before entering values.
What is an action level?
An action level is a lower trigger, often half the exposure limit, at which monitoring, medical surveillance or other steps begin. Several substance-specific OSHA standards define one. Many employers also use 50% of any limit as an internal trigger, so a result well below 100% can still require action.
Run your own numbers. It works on any phone, and the full guide downloads as a PDF.
Open the free calculator